danni66

The temperature of the industrial oven is generally RT + 5 ~ 250 ° C. in the selection, priority should be given to the industrial oven 10 ℃ higher than the actual use temperature. Because it is necessary to calculate the actual temperature difference according to the process requirements to ensure the heating effect. Industrial oven temperature error comparison is in the normal range, the general industrial oven volatility is 2%, temperature fluctuation refers to the temperature test equipment stable state, within the specified time interval, any point in the equipment workspace measured value difference between the maximum value and the minimum value. If the error is too large, it is possible that the industrial oven has failed. If the blower is broken or the switch is not turned on, the heating temperature of the heating pipe will not be opened, and the temperature will rise all the time, and the error will appear. If it is a temperature control instrument, if there is a fault, yo

The difference between a biochemical incubator and a constant temperature incubator is that the biochemical incubator has all the functions of a constant temperature incubator but also has a refrigeration function. SH constant temperature biochemical incubator refrigeration system adopts a high-quality compressor, function introduction. 1) The international leading ALLCOLDTM balanced refrigeration, which integrates automatic defrosting, multi-layer security protection, and meets the requirements of long-time operation, is equipped with internationally famous brand compressors, advocating environmental protection, high efficiency, and energy-saving. 2) Automatic frost function: balanced refrigeration program, with the original fast heat pump defrosting technology as a technical basis, customers can work continuously without interruption of the use of the state; effectively solve the problem of frost caused by the evaporator continuous operation. 3) Refrigeration capacity control manua

 There is a big difference between the use of vacuum drying oven and ordinary drying oven, that is, vacuum drying oven needs to pump vacuum and then heat up, some customers are not good at using a vacuum drying oven , here is a detailed introduction.

  XCT high-temperature hot air drying oven widely used for industrial, scientific research, health care, jade processing, and another unit for the experimental article (product) testing of the drying,heat treatment, and heating. not suitable for volatile, flammable, explosive, and other items, in order to avoid causing an explosion.

Plants are photosynthetic crops, and the requirements are not the same for different development periods. The light incubator is mainly used for germination and seedling raising of plants, tissue and microbial culture, effectiveness and aging test of drugs, wood and building materials, insect and small animal feeding and other uses of constant temperature and light test. Some light incubators can be used to set the illumination level in stages, while others with lower configurations cannot. lC series light system from Kenton adopts three-dimensional light source, even lighting distribution, and uses mirror stainless steel as reflective material in the cavity to make better lighting effect. For example, the illumination level needs to be set at six and four levels, with the same temperature and humidity. light incubator The first stage: click the setting key to enter the first stage setting interface, the cursor stops at the value of the temperature, the temperature setting value will

Recently, some people ask: once the incubator is opened, there is a sour smell. Is this normal? Is it like this with water? How to avoid or reduce the taste? Do you still have a mold like this? Do you want to add copper sulfate to prevent it? It gives off a sour smell. It is estimated that there is yeast or mold growing. Yeast is a kind of single-cell fungus, which can survive in both aerobic and anaerobic environments, belonging to facultatively anaerobic bacteria. After a period of time, the incubator needs to be scrubbed with sterilized water, and then sterilized with 300ml of double steam water at 90 ℃ for 25h (some incubators can), and then add 400ml saturated copper sulfate solution and 3L sterilized double steam water (the water volume of each incubator is different) Co2 incubator needs to be cleaned in time, keep clean and dust-free. Use disinfectant water to clean the tank thoroughly once a week. Change different kinds of disinfectant water every quarter to avoid producing d

 The intelligent light incubator provides a comprehensive and good growth environment for seeds and an ideal artificial climate experimental environment for users by means of low light illumination and running time of each time period. According to the different needs of light intensity, plants can be divided into three types, like positive plants, like negative plants, like half shade and half positive plants. Sunny plants refer to plants that are not afraid of strong sunlight. According to the characteristics of plants, they are generally divided into long sunshine plants or short sunshine plants. Xiyang plant at least 10000 LUX. The illumination (LX) range of the artificial climate chamber of the Kenton instrument is 0 ~ 15000, which can be adjusted in five levels. According to the heat generated by the light, the system effectively compensates through the precise control system to ensure the constant temperature. At the same time, the three-dimensional light source is used to eve

The cold rubber of car headlights, it is more difficult to remove, you can use the electric constant temperature oven to bake first can speed up, remove the headlight bracket, headlights into the oven for a few minutes. Remove the headlamp bracket and put the headlamp into the oven for a few minutes. Take it out and disassemble the cold rubber (be careful not to use too much force). Inevitably during disassembly, some positioning card is broken, try to be careful, but the broken positioning card can be welded back with a hot air gun after the final disassembly. According to the correct disassembly method, it will save time and effort. When dismantling to each positioning card, use the hot air gun to bake the positioning card part again with proper temperature, after the soft point, carefully let it slightly warp to make it out of the slot, and then continue to dismantle after it cools down. About halfway open, the headlamp needs to go back into the oven to bake for another 2-3 minutes,

Kenton GX series high-end constant temperature drying oven , the insulation layer using the United States Owens insulation materials, drying oven using Pro-Insulation isolation insulation technology, features. 1. Based on the concept of effective use of heat energy, the entire inner liner and shell are completely isolated to avoid energy loss due to heat transfer. 2. Adopt high-density imported thermal insulation material to wrap the inner liner, effectively heat insulation and heat preservation. Good silica gel door seal, isolated door hinge design, with a fastening device with the door handle to ensure that the seal. The temperature of the constant temperature drying oven is room temperature +5 ~ 250 °, the general temperature of the high-temperature oven is more than 300 degrees after customers use if you need to take out materials, must be the internal temperature of the oven to reach the state of room temperature can also open the door. Remember, constant temperature drying oven

 The GX Thermostatic Drying Oven series outer box and outer box are in the form of high-quality cold-rolled steel plate treated by environmental protection electrostatic spraying, and the inner cavity is made of SUS304 stainless steel material, which is more suitable for the environmental requirements of acid and alkali prevention and corrosion prevention in a scientific research laboratory. It adopts the international brand cap motor, with high-temperature bearing, better heat dissipation performance, maintenance-free, longer service life.

 There is a humidity standard under the normal national standard temperature of constant temperature and humidity chamber . Generally, the humidity test is not done below 15 degrees. At 15 degrees, the humidity can be 45% Rh-95% RH, at 20 degrees, it can be 40-98%RH, at 20 degrees to 85 degrees, it can be as high as 98%RH and as low as 20%RH. Low temperature to humidity, in addition to the humidification system, can be installed. Kenton Apparatus WS Series humidification System, features: 1. The unique humidification system design in the industry can get rid of the disadvantages of uneven and unstable humidification caused by the use of atomizing humidifier in the traditional design; 2. Automatic water filling design, automatic water level control, to ensure precise humidity addition and control; 3. The inner cavity and water tank are made of SUS304 stainless steel to ensure the quality and durability of atomization. constant temperature and humidity chamber: http://en.kentonchina.com/

The two products, Low-temperature cycle sink, and Magnetic stirring water bath pot, both have a different scope of use. Low-temperature cycle sink: it is the ideal constant temperature equipment for research institutes, colleges and universities, engineering laboratories and quality inspection departments. High-quality stainless steel plate and precision mechanical processing technology manufacturing; temperature control device adopts high stability computing troubles song atmosphere and double-integral high-precision A / D conversion technology; far-infrared heating technology design, magnetic stirring, product thermal balance time is short, small temperature fluctuation, good uniformity. Digital display water bath pot -HH: Low-temperature cycle sink-DC for medical and health care, medical school inspection and laboratory and industrial and mining enterprises, scientific research units for constant-temperature auxiliary heating; with high-precision sensor temperature control system, d

Disinfection of ultra-clean working table, general ultra-clean working table is to use ultraviolet sterilization lamp for disinfection (each open more than 15 minutes, usually 30 minutes) and so on disinfection, in addition, the aseptic room should be regular with 70% alcohol or 0.5% phenol spray dust and disinfection, with 2% of new cleanser wipe countertop and utensils (70% alcohol can also be), with formalin (40% formaldehyde) plus a small amount of potassium permanganate on a regular basis. Closed fumigation, with to make the aseptic room often maintains a high degree of sterility. In addition, in the ultraviolet lamp on for a long time, can stimulate the oxygen molecules in the air to connect into ozone molecules, this gas composition has a very strong sterilization effect, can produce sterilization effect on the ultraviolet ray does not directly shine to the corner. As the ozone is an obstacle to health, before entering the operation should be turned off the ultraviolet lamp, off

Biochemical incubator in the work project, if the case of flowing water, it is necessary to analyze what went wrong. Biochemical incubator temperature range 0 ~ 65 degrees, generally we use the temperature in the laboratory and then between 25-37 degrees, the ambient temperature of 30 degrees is if the use of temperature 25 degrees constant temperature, the incubator to cool down, cooling is done through the refrigeration unit. Refrigeration produces temperature difference will have condensation, ready-made water. The biochemical incubator has a water catchment port, water through the water catchment port discharged to the outside of the incubator, will not flow to the bottom of the biochemical incubator. What is the reason when water is found at the bottom of the biochemical incubator? It is the water produced by the refrigeration unit on the evaporator in the incubator flows along the copper tube to the bottom of the incubator, and it is the copper tube lead outlet in the incubator

Except for their capacity, there is another difference, let Kenton introduce for you 1. The heating methods are different. The general climate room is heated by natural sunlight, and the "greenhouse effect" of glass or plastic is used to heat up, while the heating of artificial climate chamber uses the heat convection mode of electric furnace wire and blower. 2. In terms of temperature uniformity and measurement accuracy, the operability of climate chamber is far better than that of climate room. 3. In application, the climate room is mainly used for crop seedling and growth; the artificial climate chamber has accurate biological culture, because of its good airtightness, it is also suitable for microbial culture, insect breeding, etc. 4. Occasion: the climate room is most commonly used in agriculture, and the climate chamber is used in scientific research laboratories and hospitals.

 As for how to dry extract, in fact, there are many drying methods, generally drying, spray drying (mass production), decompression drying, belt drying, boiling drying, freeze-drying, and so on. The water extract is generally freeze-dried first and then dried in a vacuum drying oven to obtain dry powder; Organic solvent to extract the general use of rotary steam bar, water bath temperature according to the different organic solvents and different, often obtain is the extract, not easy to obtain dry powder; The vacuum drying chamber is high-precision constant temperature equipment with heating and vacuum control. It is specially designed for drying heat-sensitive and easily oxidized substances. It is especially suitable for powder or granular samples and can effectively shorten the drying time.