Use and Maintenance Skills of Electrothermal Thermostatic incubator

Electric thermostat incubator is often used in modern middle and advanced laboratories. It is suitable for users with high temperature environment. It is produced by advanced numerical control processing equipment. It has a wide range of applications. It can be used as necessary equipment for industrial and mining enterprises, medical and health, biological and scientific research units.

Method of using electrothermal incubator:
1. Operators need to read the instructions carefully before using the incubator, understand and familiarize themselves with the functions of incubator, before they can turn on the power supply.

2. After switching on the power supply, press the power switch and the power indicator lights up.

3. Set the temperature controller to the set temperature required by the user (this value should be higher than room temperature plus 50C).

4. When the display temperature of the incubator reaches the set temperature, the heating interruption and the heating indicator extinguishes. After 90 minutes of power-on at the standard ambient temperature, the temperature can remain stable, such as when the instant temperature in the incubator exceeds the set upper alarm temperature (the factory is set to 5 C), the temperature tracking alarm indicator of the thermostat is on, and the power supply of the heater is automatically cut off.

5. In the process of using, if we need to open the box door to take samples, the heater and circulating fan will stop working. When the glass door is closed, the heater and fan can operate normally, so as to avoid the pollution of culture and the phenomenon of temperature overshoot.

Cautions and maintenance of electrothermal incubator:
1. Instruments should not be used under high voltage, high current and strong magnetic field, so as to avoid interference with temperature controller and electric shock hazard.

2. Plating parts and surface finish should always be kept clean. If it is not used for a long time, neutral grease or vaseline should be applied on the plating parts to prevent corrosion. Plastic film dust-proof cover should be put on the outside of the incubator to keep the incubator in the drying room so as to avoid damp damage to the thermostat.

3. The products will be strictly debugged before they leave the factory. The menu setting data of the thermostat should not be modified at will.

4. The incubator shell must be grounded effectively to ensure safe operation.

5. Do not place inflammable and explosive materials for heating, to prevent danger.

6. Do not place high-risk articles to prevent the box from decaying.

http://en.kentonchina.com

评论

发表评论

此博客中的热门博文

What incubator should I use for fungi?

图片
There are many different types of incubators and the choice of the incubator should depend on what is being cultured. If the microorganism to be cultured is aerobic, then a normal incubator is sufficient; if it is anaerobic, then you need to buy an anaerobic incubator; if it is algae or fungi, it is better to have a light incubator. A light incubator is a piece of high-precision constant temperature equipment with light function; a light incubator is a special constant temperature incubation device for the cultivation of bacteria, molds, microorganisms, and breeding tests, especially practical for biological engineering, medical research, agriculture, and forestry science, aquaculture, animal husbandry and other fields engaged in scientific research and production use of the ideal equipment.　 The main technical parameters of the fungal incubator in the microbiology room of the laboratory require 1: Temperature requirements: 2 ~ 48 c, the temperature inside the incubator temperature u
阅读全文

Laminar flow Cabinet architecture introduction

图片
Laminar Flow Cabinet Clean Bench, also known as laminar flow Cabinet, can be mainly divided into two- person single, single side double side, horizontal vertical, etc. The structure is divided into the box, table, bracket, support foot, exhaust pipe, HEPA filter, pre-filter, etc.   Laminar flow cabinet design should have sufficient strength and stiffness, the weight should be light under the premise of good stability, the joints should be tight, according to the needs of the support foot can be self-locking structure universal wheel, but for the high requirements of seismic workbench without support feet and universal wheel, the operating area of the working surface can be made independent of the box platform. The inner surface of the single table is made of three sides of the wall. The wall surface is smooth and the joint is sealed. The glass and metal connection parts should also be sealed. The negative pressure air duct should be designed so that the air duct, plenum, filter, and su
阅读全文

The Control system is the core of the constant temperature and humidity chamber

图片
The Control system is the core of the constant temperature and humidity chamber , it determines the temperature rise rate of the text chamber, precision, and other important indicators. Now the controller of the test chamber mostly adopts PID control, but also a few adopts PID and fuzzy control phase combination control mode. Because the control system of the thermostatic oscillator basically belongs to the category of software, and this part in the use of the process, generally there will be no problems. In the constant temperature and humidity chamber refrigeration principle diagram, we introduced the temperature and humidity chamber refrigeration system several important components of the working path. So how do these components work? The refrigerant is adiabatically compressed to a higher pressure by the compressor, and the work is consumed to raise the exhaust temperature. After that, the refrigerant isothermally exchanges heat with the surrounding medium through the refrigerant c
阅读全文