Illumination testing of biosafety cabinets

 Illuminance testing: test according to YY 0569-2011 6.3.4, in the center line of the non-stick tape in the middle of the work surface of the biosafety cabinet, 150 mm from each of the left and right side walls, each measurement point is no more than 300 mm away. For example, if the distance between the left and right side walls of a cabinet is 1240 mm, after subtracting the distance between the left and right points of 300 mm, the remaining distance is 940 mm.

Background illuminance measurement: turn off the lights of the biological safety cabinet, digital illuminance meter press POWER key, the lower right of the display shows "20", press RANGE key, adjust to the lower right of the display shows "2000", illuminance value in The illuminance value is displayed in "LUX" units. Select the appropriate measuring position and the value shown at the bottom right of the display of the illuminance meter is an indication of the measuring range. Place the light detector head flat on the position of the measuring point of the non-stick tape, open the cover of the light detector head and measure the background illuminance at the measuring point in sequence from left to right, press the "HOLD" key within 5-10 seconds after each movement to the position of the measuring point, read and record the illuminance value when it remains unchanged. Press the "HOLD" key again to exit the data hold and carry out the next point measurement, record the measured values of all the measurement points and calculate the average value according to the measured values.
Illuminance measurement: Turn on the lights of the biological safety cabinet and start the cabinet fan. Turn on the ON/OFF power switch, press the LUX key once, and fill in the record of the instrument after the measurement.
Note: 1. The illuminance meter display shows a maximum of 1,000 digits, if the highest digit "1" is displayed on the left, it means overload, you should immediately choose a higher level of measurement.
    2, when set 20 000 LUX / FC gear, the value displayed must be x 10 times to be the true value of the measurement.
When setting 200 000 LUX/Fc, the displayed value must be x 100 times the true value of the measurement.
According to YY 0569-2011 5.4.4, "The average illuminance of the safety cabinet shall be not less than 650 lx and the measured value of each illuminance shall be not less than 430 lx", the measurement results are evaluated and a conclusion is given as to whether they pass or not.


评论

发表评论

此博客中的热门博文

What incubator should I use for fungi?

图片
There are many different types of incubators and the choice of the incubator should depend on what is being cultured. If the microorganism to be cultured is aerobic, then a normal incubator is sufficient; if it is anaerobic, then you need to buy an anaerobic incubator; if it is algae or fungi, it is better to have a light incubator. A light incubator is a piece of high-precision constant temperature equipment with light function; a light incubator is a special constant temperature incubation device for the cultivation of bacteria, molds, microorganisms, and breeding tests, especially practical for biological engineering, medical research, agriculture, and forestry science, aquaculture, animal husbandry and other fields engaged in scientific research and production use of the ideal equipment.　 The main technical parameters of the fungal incubator in the microbiology room of the laboratory require 1: Temperature requirements: 2 ~ 48 c, the temperature inside the incubator temperature u
阅读全文

Laminar flow Cabinet architecture introduction

图片
Laminar Flow Cabinet Clean Bench, also known as laminar flow Cabinet, can be mainly divided into two- person single, single side double side, horizontal vertical, etc. The structure is divided into the box, table, bracket, support foot, exhaust pipe, HEPA filter, pre-filter, etc.   Laminar flow cabinet design should have sufficient strength and stiffness, the weight should be light under the premise of good stability, the joints should be tight, according to the needs of the support foot can be self-locking structure universal wheel, but for the high requirements of seismic workbench without support feet and universal wheel, the operating area of the working surface can be made independent of the box platform. The inner surface of the single table is made of three sides of the wall. The wall surface is smooth and the joint is sealed. The glass and metal connection parts should also be sealed. The negative pressure air duct should be designed so that the air duct, plenum, filter, and su
阅读全文

The Control system is the core of the constant temperature and humidity chamber

图片
The Control system is the core of the constant temperature and humidity chamber , it determines the temperature rise rate of the text chamber, precision, and other important indicators. Now the controller of the test chamber mostly adopts PID control, but also a few adopts PID and fuzzy control phase combination control mode. Because the control system of the thermostatic oscillator basically belongs to the category of software, and this part in the use of the process, generally there will be no problems. In the constant temperature and humidity chamber refrigeration principle diagram, we introduced the temperature and humidity chamber refrigeration system several important components of the working path. So how do these components work? The refrigerant is adiabatically compressed to a higher pressure by the compressor, and the work is consumed to raise the exhaust temperature. After that, the refrigerant isothermally exchanges heat with the surrounding medium through the refrigerant c
阅读全文