The new high-temperature drying oven in the laboratory has been smoking since it was started up, what is the reason?

The high-temperature drying oven in the laboratory, when the temperature rises to 150 ℃, the oven smokes and has a burnt smell. Is this dangerous?

If it is ruled out that there is a circuit problem in the oven, the problem is not big. The reason is that the insulation layer of the newly produced high-temperature oven contains some impurities, and there is a wax tube on the power line. When heating for the first time, the impurities in the insulation layer and the paraffin on the wax pipe will volatilize due to heating, which will smell burnt or even smoke It's good to have these ingredients evaporated a few times.

Therefore, before formal use, it is suggested that samples should not be put in first. Close the door, loosen the exhaust cover on the top of the box, turn on the power switch, and set the temperature controller at 100 ℃. At this time, the temperature inside the chamber starts to rise. When the temperature rises to 100 ℃, the temperature controller will automatically keep constant temperature. After that, the power supply can be cut off and the door can be opened to dissipate heat and smoke.
high-temperature drying oven
http://en.kentonchina.com/industrial-oven/20170602/25.html


评论

发表评论

此博客中的热门博文

What incubator should I use for fungi?

图片
There are many different types of incubators and the choice of the incubator should depend on what is being cultured. If the microorganism to be cultured is aerobic, then a normal incubator is sufficient; if it is anaerobic, then you need to buy an anaerobic incubator; if it is algae or fungi, it is better to have a light incubator. A light incubator is a piece of high-precision constant temperature equipment with light function; a light incubator is a special constant temperature incubation device for the cultivation of bacteria, molds, microorganisms, and breeding tests, especially practical for biological engineering, medical research, agriculture, and forestry science, aquaculture, animal husbandry and other fields engaged in scientific research and production use of the ideal equipment.　 The main technical parameters of the fungal incubator in the microbiology room of the laboratory require 1: Temperature requirements: 2 ~ 48 c, the temperature inside the incubator temperature u
阅读全文

Laminar flow Cabinet architecture introduction

图片
Laminar Flow Cabinet Clean Bench, also known as laminar flow Cabinet, can be mainly divided into two- person single, single side double side, horizontal vertical, etc. The structure is divided into the box, table, bracket, support foot, exhaust pipe, HEPA filter, pre-filter, etc.   Laminar flow cabinet design should have sufficient strength and stiffness, the weight should be light under the premise of good stability, the joints should be tight, according to the needs of the support foot can be self-locking structure universal wheel, but for the high requirements of seismic workbench without support feet and universal wheel, the operating area of the working surface can be made independent of the box platform. The inner surface of the single table is made of three sides of the wall. The wall surface is smooth and the joint is sealed. The glass and metal connection parts should also be sealed. The negative pressure air duct should be designed so that the air duct, plenum, filter, and su
阅读全文

The Control system is the core of the constant temperature and humidity chamber

图片
The Control system is the core of the constant temperature and humidity chamber , it determines the temperature rise rate of the text chamber, precision, and other important indicators. Now the controller of the test chamber mostly adopts PID control, but also a few adopts PID and fuzzy control phase combination control mode. Because the control system of the thermostatic oscillator basically belongs to the category of software, and this part in the use of the process, generally there will be no problems. In the constant temperature and humidity chamber refrigeration principle diagram, we introduced the temperature and humidity chamber refrigeration system several important components of the working path. So how do these components work? The refrigerant is adiabatically compressed to a higher pressure by the compressor, and the work is consumed to raise the exhaust temperature. After that, the refrigerant isothermally exchanges heat with the surrounding medium through the refrigerant c
阅读全文