How to deal with the accumulated oil in the vacuum drying oven?

During the use of the vacuum drying oven, day by day, some oil stains may appear. If these problems are not dealt with properly, it will affect the pollution of the next drying item and even the use of the machine. So, how to deal with these oils?

If there are corrosive residues overflowing into the room during the test, it should be cleaned in time if found, otherwise, the bile wall of the work room will be corroded and rusty, causing damage!

What are the cleaning supplies?

If it is not difficult to clean, you can use clean water; if it is more difficult, you need to use special cleaners such as alcohol and detergent. After use, wipe it off with clean water, leaving no residue, just dry it.


Note: Do not use sodium chloride solvents or other halide solutions to clean the device, as this may cause damage to the liner and accessories.

Kenton's DZF and KZ series vacuum drying oven parts are made of SUS304 stainless steel, which is very resistant to corrosion. However, it should be noted that SUS304 stainless steel does not have anti-corrosion ability to certain highly corrosive raw materials. Therefore, cleaning is also a maintenance process, so that the equipment can maintain performance and prolong its service life.

评论

发表评论

此博客中的热门博文

What incubator should I use for fungi?

图片
There are many different types of incubators and the choice of the incubator should depend on what is being cultured. If the microorganism to be cultured is aerobic, then a normal incubator is sufficient; if it is anaerobic, then you need to buy an anaerobic incubator; if it is algae or fungi, it is better to have a light incubator. A light incubator is a piece of high-precision constant temperature equipment with light function; a light incubator is a special constant temperature incubation device for the cultivation of bacteria, molds, microorganisms, and breeding tests, especially practical for biological engineering, medical research, agriculture, and forestry science, aquaculture, animal husbandry and other fields engaged in scientific research and production use of the ideal equipment.　 The main technical parameters of the fungal incubator in the microbiology room of the laboratory require 1: Temperature requirements: 2 ~ 48 c, the temperature inside the incubator temperature u
阅读全文

Laminar flow Cabinet architecture introduction

图片
Laminar Flow Cabinet Clean Bench, also known as laminar flow Cabinet, can be mainly divided into two- person single, single side double side, horizontal vertical, etc. The structure is divided into the box, table, bracket, support foot, exhaust pipe, HEPA filter, pre-filter, etc.   Laminar flow cabinet design should have sufficient strength and stiffness, the weight should be light under the premise of good stability, the joints should be tight, according to the needs of the support foot can be self-locking structure universal wheel, but for the high requirements of seismic workbench without support feet and universal wheel, the operating area of the working surface can be made independent of the box platform. The inner surface of the single table is made of three sides of the wall. The wall surface is smooth and the joint is sealed. The glass and metal connection parts should also be sealed. The negative pressure air duct should be designed so that the air duct, plenum, filter, and su
阅读全文

The Control system is the core of the constant temperature and humidity chamber

图片
The Control system is the core of the constant temperature and humidity chamber , it determines the temperature rise rate of the text chamber, precision, and other important indicators. Now the controller of the test chamber mostly adopts PID control, but also a few adopts PID and fuzzy control phase combination control mode. Because the control system of the thermostatic oscillator basically belongs to the category of software, and this part in the use of the process, generally there will be no problems. In the constant temperature and humidity chamber refrigeration principle diagram, we introduced the temperature and humidity chamber refrigeration system several important components of the working path. So how do these components work? The refrigerant is adiabatically compressed to a higher pressure by the compressor, and the work is consumed to raise the exhaust temperature. After that, the refrigerant isothermally exchanges heat with the surrounding medium through the refrigerant c
阅读全文