How to maintain a constant temperature and humidity incubator？

Constant temperature and humidity incubator is more expensive machine, so must do a good job of daily maintenance. So, how should maintain constant temperature and humidity incubator?


In the handling of the constant temperature and humidity incubator, do not turn it upside down or lay it flat above 45 degrees.

Do not change the set value frequently in use, lest the compressor start up frequently and cause overload, affecting the service life of the equipment.

This machine is equipped with power switch. If there is any fault during operation, please cut off the power first, check whether the control circuit is in good condition, and then check other parts. (see wiring diagram for details)

Be sure to close the inner door and then the trunk. If the inner door is not fully closed, the equipment may not work at full performance even if the door is closed. Please be careful when closing the door. Do not use too much force to damage the door seal.

Water tank is recommended to use pure water or distilled water, to ensure water humidification clean.

In order to maintain the appearance of the equipment, do not wipe the appearance with corrosion solution, the incubator can be wiped with dry cloth or alcohol, keep the incubator clean.

When the equipment is not in use, the cabinet should be kept dry and the power cut off.

In order to ensure that the temperature in the incubator is uniform, it is necessary to check whether the axial fan in the incubator is running normally. During the experiment, the articles in the incubator should not be placed too close and do not block the fan outlet, in order to facilitate the flow circulation in the incubator.

Do not touch. The temperature sensor in the cabinet will be out of control.

Be sure to secure the shelf or the culture may be damaged.

Do not lean against or put pressure on glass, which may cause injury to personnel.

Do not lean against the door of the equipment to prevent the equipment from tipping over or damage to the door resulting in personnel injury and equipment damage.

评论

发表评论

此博客中的热门博文

What incubator should I use for fungi?

图片
There are many different types of incubators and the choice of the incubator should depend on what is being cultured. If the microorganism to be cultured is aerobic, then a normal incubator is sufficient; if it is anaerobic, then you need to buy an anaerobic incubator; if it is algae or fungi, it is better to have a light incubator. A light incubator is a piece of high-precision constant temperature equipment with light function; a light incubator is a special constant temperature incubation device for the cultivation of bacteria, molds, microorganisms, and breeding tests, especially practical for biological engineering, medical research, agriculture, and forestry science, aquaculture, animal husbandry and other fields engaged in scientific research and production use of the ideal equipment.　 The main technical parameters of the fungal incubator in the microbiology room of the laboratory require 1: Temperature requirements: 2 ~ 48 c, the temperature inside the incubator temperature u
阅读全文

Laminar flow Cabinet architecture introduction

图片
Laminar Flow Cabinet Clean Bench, also known as laminar flow Cabinet, can be mainly divided into two- person single, single side double side, horizontal vertical, etc. The structure is divided into the box, table, bracket, support foot, exhaust pipe, HEPA filter, pre-filter, etc.   Laminar flow cabinet design should have sufficient strength and stiffness, the weight should be light under the premise of good stability, the joints should be tight, according to the needs of the support foot can be self-locking structure universal wheel, but for the high requirements of seismic workbench without support feet and universal wheel, the operating area of the working surface can be made independent of the box platform. The inner surface of the single table is made of three sides of the wall. The wall surface is smooth and the joint is sealed. The glass and metal connection parts should also be sealed. The negative pressure air duct should be designed so that the air duct, plenum, filter, and su
阅读全文

The Control system is the core of the constant temperature and humidity chamber

图片
The Control system is the core of the constant temperature and humidity chamber , it determines the temperature rise rate of the text chamber, precision, and other important indicators. Now the controller of the test chamber mostly adopts PID control, but also a few adopts PID and fuzzy control phase combination control mode. Because the control system of the thermostatic oscillator basically belongs to the category of software, and this part in the use of the process, generally there will be no problems. In the constant temperature and humidity chamber refrigeration principle diagram, we introduced the temperature and humidity chamber refrigeration system several important components of the working path. So how do these components work? The refrigerant is adiabatically compressed to a higher pressure by the compressor, and the work is consumed to raise the exhaust temperature. After that, the refrigerant isothermally exchanges heat with the surrounding medium through the refrigerant c
阅读全文