What is the principle of using high temperature blast dryer?

High temperature blast drying box is widely used in industrial, mining, scientific research, medical and health, jade processing and other units for drying test products, heat treatment and heating, and various laboratories for baking and disinfection, but it is not suitable for volatile goods, in order to avoid unnecessary danger. Its performance can be transformed into heat energy by electric heating, so that it can be dried at constant temperature.

Flammable and explosive volatiles are strictly forbidden to be put into the box for heating and drying. If the material value is too high, an independent temperature limiter can be installed to set the maximum temperature on line. Double insurance ensures that the material will not be damaged due to the failure of electronic components in the box.

The outer shell of the electrothermal constant temperature blast drying box is made of high quality cold-rolled steel plate, while the inner gallbladder of the working room is made of stainless steel plate, which has the characteristics of acid and alkali prevention and corrosion prevention. The door of the box is sealed with double-layer thermal insulation material. Double-layer toughened glass window is installed in the middle of the door, and the working room can be observed under the condition of thermal insulation. Heating elements are distributed on the bottom or left side of the studio. High temperature resistant materials are used to ensure safety and long service life. The temperature in the box is controlled by a temperature sensor and a temperature controller. It is installed in the control box of the box and has a movable winding device, which is convenient for maintenance.

The highest working temperature of the high temperature blast drying box is 500 C. The size of the studio has various specifications, which can be used for the placement of various test products. Often suitable for baking, drying, heat treatment and other heating, industrial, is one of the necessary laboratory equipment.

The working temperature of the drying box can rise from room temperature to the maximum temperature. Within this range, the working temperature can be selected randomly for automatic temperature control system to keep the temperature constant.

http://en.kentonchina.com

评论

发表评论

此博客中的热门博文

What incubator should I use for fungi?

图片
There are many different types of incubators and the choice of the incubator should depend on what is being cultured. If the microorganism to be cultured is aerobic, then a normal incubator is sufficient; if it is anaerobic, then you need to buy an anaerobic incubator; if it is algae or fungi, it is better to have a light incubator. A light incubator is a piece of high-precision constant temperature equipment with light function; a light incubator is a special constant temperature incubation device for the cultivation of bacteria, molds, microorganisms, and breeding tests, especially practical for biological engineering, medical research, agriculture, and forestry science, aquaculture, animal husbandry and other fields engaged in scientific research and production use of the ideal equipment.　 The main technical parameters of the fungal incubator in the microbiology room of the laboratory require 1: Temperature requirements: 2 ~ 48 c, the temperature inside the incubator temperature u
阅读全文

Laminar flow Cabinet architecture introduction

图片
Laminar Flow Cabinet Clean Bench, also known as laminar flow Cabinet, can be mainly divided into two- person single, single side double side, horizontal vertical, etc. The structure is divided into the box, table, bracket, support foot, exhaust pipe, HEPA filter, pre-filter, etc.   Laminar flow cabinet design should have sufficient strength and stiffness, the weight should be light under the premise of good stability, the joints should be tight, according to the needs of the support foot can be self-locking structure universal wheel, but for the high requirements of seismic workbench without support feet and universal wheel, the operating area of the working surface can be made independent of the box platform. The inner surface of the single table is made of three sides of the wall. The wall surface is smooth and the joint is sealed. The glass and metal connection parts should also be sealed. The negative pressure air duct should be designed so that the air duct, plenum, filter, and su
阅读全文

The Control system is the core of the constant temperature and humidity chamber

图片
The Control system is the core of the constant temperature and humidity chamber , it determines the temperature rise rate of the text chamber, precision, and other important indicators. Now the controller of the test chamber mostly adopts PID control, but also a few adopts PID and fuzzy control phase combination control mode. Because the control system of the thermostatic oscillator basically belongs to the category of software, and this part in the use of the process, generally there will be no problems. In the constant temperature and humidity chamber refrigeration principle diagram, we introduced the temperature and humidity chamber refrigeration system several important components of the working path. So how do these components work? The refrigerant is adiabatically compressed to a higher pressure by the compressor, and the work is consumed to raise the exhaust temperature. After that, the refrigerant isothermally exchanges heat with the surrounding medium through the refrigerant c
阅读全文