What are the requirements for using digital display blast dryer

The blast dryer is a kind of drying equipment. It is mainly used for baking, drying, sterilization and heat treatment. It is very suitable for routine testing in industrial and mining enterprises, basic laboratories and workshops. However, it is not recommended to use it uninterruptedly for a long time. For some samples with high temperature uniformity and high water content, it is not recommended to use this equipment. Valuable items can be put forward to the manufacturer to control temperature by pretending to have independent temperature limiting control function, which is one of the necessary equipment for laboratory equipment.

The air in the working room of the digital display air blast dryer is heated by an electric heater, forced circulation by a fan, and uniform heat exchange is carried out between the air and the heated articles in the working area to achieve the purpose of baking or drying.

Operation and requirements of blast dryer:
1. Open the door of the blast drying box, put the items that need to be heated into the shelf of the box, close the door of the box, and turn the exhaust valve on the control panel to half (the temperature of the dried product can be adjusted properly at any time during the heating process);

2. Connect the power supply equipment which is consistent with the requirement of the blast drying box, and grounding the grounding end of the power supply socket used reliably.

3. Turn on the power switch, the power indicator lights on and the temperature control instrument starts to show the temperature of the studio.

4. There are two heating switches. If heating needs to be turned on at a lower temperature, heating 2 should be turned on at a higher temperature and heated at the same time.

5. According to the needs of the heated articles, turn the temperature setting knob (or press the dial switch) on the temperature controller to set the temperature, and the drying box starts to heat up.

6. After the work is finished, the heating switch 1, the heating switch 2 and the main power switch can be turned off.

http://en.kentonchina.com

评论

发表评论

此博客中的热门博文

What incubator should I use for fungi?

图片
There are many different types of incubators and the choice of the incubator should depend on what is being cultured. If the microorganism to be cultured is aerobic, then a normal incubator is sufficient; if it is anaerobic, then you need to buy an anaerobic incubator; if it is algae or fungi, it is better to have a light incubator. A light incubator is a piece of high-precision constant temperature equipment with light function; a light incubator is a special constant temperature incubation device for the cultivation of bacteria, molds, microorganisms, and breeding tests, especially practical for biological engineering, medical research, agriculture, and forestry science, aquaculture, animal husbandry and other fields engaged in scientific research and production use of the ideal equipment.　 The main technical parameters of the fungal incubator in the microbiology room of the laboratory require 1: Temperature requirements: 2 ~ 48 c, the temperature inside the incubator temperature u
阅读全文

Laminar flow Cabinet architecture introduction

图片
Laminar Flow Cabinet Clean Bench, also known as laminar flow Cabinet, can be mainly divided into two- person single, single side double side, horizontal vertical, etc. The structure is divided into the box, table, bracket, support foot, exhaust pipe, HEPA filter, pre-filter, etc.   Laminar flow cabinet design should have sufficient strength and stiffness, the weight should be light under the premise of good stability, the joints should be tight, according to the needs of the support foot can be self-locking structure universal wheel, but for the high requirements of seismic workbench without support feet and universal wheel, the operating area of the working surface can be made independent of the box platform. The inner surface of the single table is made of three sides of the wall. The wall surface is smooth and the joint is sealed. The glass and metal connection parts should also be sealed. The negative pressure air duct should be designed so that the air duct, plenum, filter, and su
阅读全文

The Control system is the core of the constant temperature and humidity chamber

图片
The Control system is the core of the constant temperature and humidity chamber , it determines the temperature rise rate of the text chamber, precision, and other important indicators. Now the controller of the test chamber mostly adopts PID control, but also a few adopts PID and fuzzy control phase combination control mode. Because the control system of the thermostatic oscillator basically belongs to the category of software, and this part in the use of the process, generally there will be no problems. In the constant temperature and humidity chamber refrigeration principle diagram, we introduced the temperature and humidity chamber refrigeration system several important components of the working path. So how do these components work? The refrigerant is adiabatically compressed to a higher pressure by the compressor, and the work is consumed to raise the exhaust temperature. After that, the refrigerant isothermally exchanges heat with the surrounding medium through the refrigerant c
阅读全文