What should we pay attention to when using industrial oven
Industrial oven is a kind of equipment suitable for industrial and mining enterprises and workshops for mass production. It can be used uninterruptedly for a long time. It is a device that dries objects by heating the insulating layer of electric heating wire. It is mainly used for product dehydration and drying. There are many types of ovens, but the basic structure is similar. They are generally composed of the box, the electric heating system and the automatic temperature control system. Here are some points for attention in using the oven.
1. The oven should be protected from vibration and corrosion in the dry and horizontal areas of the room.
2. Attention should be paid to the safe use of electricity. According to the power consumption of the oven, a power brake knife with sufficient capacity should be installed, and enough power supply wires should be selected with good grounding wires.
3. The industrial oven with mercury thermometer thermostat with electric contacts shall connect two wires of electric contacts thermometer to two connecting posts on the top of the oven respectively. In addition, a common mercury thermometer is inserted into the exhaust valve (the thermometer in the exhaust valve is used to check the contact mercury thermometer and the actual temperature in the observation box) to open the outlet of the exhaust valve. The screw on the steel cap is tightened after adjusting the mercury thermometer of the electric contact to the required temperature to achieve the purpose of constant temperature. However, attention must be paid to adjusting the indicator iron not to turn outside the scale.
4. When all the preparations are ready, the sample can be put into the oven, then connected and turned on the power supply. The red light indicates that the oven has been heated. When the temperature reaches the controlled temperature, the red light goes out and the green light goes on, and the temperature starts to be constant. In order to prevent the failure of temperature control, care must also be taken.
5. When putting in the test, we should pay attention to the arrangement not too close. The test material should not be placed on the radiator plate to avoid affecting the upward flow of hot air. It is forbidden to bake flammable, explosive, volatile and corrosive articles.
6. When it is necessary to observe the sample situation in the working room, the outside door can be opened and observed through the glass door. However, it is better to keep the door open as little as possible so as not to affect the constant temperature. Especially when working above 200 C, opening the box door may cause the glass door to suddenly cool and burst.
7. The blower must be opened in the process of heating and constant temperature in the industrial oven with blower, otherwise it will affect the uniformity of the temperature in the studio and damage the heating elements.
8. The power supply should be cut off in time after the work is finished to ensure safety.
9. Keep the inside and outside of the share clean. When using, the temperature should not exceed the maximum temperature of the industrial oven.
10. In order to prevent scald, special tools and protective clothing are needed when taking and putting test products.
http://en.kentonchina.com
1. The oven should be protected from vibration and corrosion in the dry and horizontal areas of the room.
2. Attention should be paid to the safe use of electricity. According to the power consumption of the oven, a power brake knife with sufficient capacity should be installed, and enough power supply wires should be selected with good grounding wires.
3. The industrial oven with mercury thermometer thermostat with electric contacts shall connect two wires of electric contacts thermometer to two connecting posts on the top of the oven respectively. In addition, a common mercury thermometer is inserted into the exhaust valve (the thermometer in the exhaust valve is used to check the contact mercury thermometer and the actual temperature in the observation box) to open the outlet of the exhaust valve. The screw on the steel cap is tightened after adjusting the mercury thermometer of the electric contact to the required temperature to achieve the purpose of constant temperature. However, attention must be paid to adjusting the indicator iron not to turn outside the scale.
4. When all the preparations are ready, the sample can be put into the oven, then connected and turned on the power supply. The red light indicates that the oven has been heated. When the temperature reaches the controlled temperature, the red light goes out and the green light goes on, and the temperature starts to be constant. In order to prevent the failure of temperature control, care must also be taken.
5. When putting in the test, we should pay attention to the arrangement not too close. The test material should not be placed on the radiator plate to avoid affecting the upward flow of hot air. It is forbidden to bake flammable, explosive, volatile and corrosive articles.
6. When it is necessary to observe the sample situation in the working room, the outside door can be opened and observed through the glass door. However, it is better to keep the door open as little as possible so as not to affect the constant temperature. Especially when working above 200 C, opening the box door may cause the glass door to suddenly cool and burst.
7. The blower must be opened in the process of heating and constant temperature in the industrial oven with blower, otherwise it will affect the uniformity of the temperature in the studio and damage the heating elements.
8. The power supply should be cut off in time after the work is finished to ensure safety.
9. Keep the inside and outside of the share clean. When using, the temperature should not exceed the maximum temperature of the industrial oven.
10. In order to prevent scald, special tools and protective clothing are needed when taking and putting test products.
http://en.kentonchina.com
评论
发表评论